Sea User Manuel
Clear Epoxy Resin System For Resinart
Specially designed for resinart
Clear
Solvent free
Odorless
Bright
Does not contain volatile substances
Mixing ratio is 1:1 (by weight)
Jel time is
15 - 25 minutes
Demolding time
is 12 - 15 hours
Usage
• The product is packaged as A (Resin) and B (Hardener). Mix the two products together in a 1: 1 ratio. (For example, mix for 40 grams of mixture, 20 grams of A and 20 grams of B.
• Make the mixtures using sensitive scales.
• For a better mixture, first add hardener to the mixing bowl, then add the resin and mix at a slow speed for at least 3 minutes. Your epoxy may have turned white. After applying it to the surface, it will become transparent again when you pass over it with a torch or lighter.
• You do not need to leave the prepared mixture to rest.
Considerations
• Prepare the resin and hardener mixture to a maximum of 100 grams. The product usage time will be shorter in mixtures with higher amounts and the mixture may become unusable.
• The working time of the mixture is 15 – 25 minutes. The prepared mixture should be used within the working time. Otherwise, the product will overheat and dry without mixing in the container.
• Volumetric measurements made with tools such as beaker, glass, syringe, etc. will cause incorrect mixing ratio. In order to adjust the mixture amount correctly, you must use sensitive scales.
• The product is especially designed as very high viscosity.
• To minimize the formation of bubbles and air bubbles, take care to make the casting slowly.
• You can use a hot air gun and / or torch to remove bubbles on the surface after casting.
• In order to reduce the formation of air bubbles and bubbles in applications, a vacuum machine must be used.
• The mixed resin should not be moved after it has started to gel. Otherwise, fluctuations in texture and surface may occur.
• The mixed resin takes place approximately 12-16 hours after the initial drying. After the first drying, the final hardening process begins and this hardening process continues for 7 days.
• Work at room temperature. Low temperature can cause late drying and misting, and high temperature may cause early drying, yellowing and burning.
• For any reason, do not mix any other material that does not fit into the system.
• Make sure that the equipment you use during the application is dry and clean.
• Do not forget to use safety equipment.
• Avoid contact with your skin. May have an allergic reaction.
• Store the product you do not use at a temperature of 10 and 30 degrees in a closed area away from direct sunlight.
• Do not keep the products openly.
• Do not leave the products obtained as a result of the mixture under direct sun.
• In-product yellowing may occur in the product waiting for a long time.
Cold ambient conditions cause the epoxy resins to whiten, solidify and have a candied appearance. When you observe these situations, your epoxy resin is crystallized. Soak the bottles in 60°C-80°C water until they become transparent, so that they can be reused.
Frequently Asked Questions
We have answered questions about the use of epoxy for you. Check out the frequently asked questions.
How much epoxy should I use?
Don’t know how much epoxy to use? You can easily calculate how much epoxy you need to use by entering the dimensions.
Slim Vis User Manuel
Ultra Clear Epoxy Resin System With Extra Yellowing Resistance
Suitable for small volume applications
Ultra clear
High viscosity
Odorless
Bright
Solvent free
Does not contain volatile substances
Mixing ratio is 2:1 (by weight)
Jel time is
50-70 minutes
Demolding time is 18 - 24 hours
Usage
• The product is packaged as A (Resin) and B (Hardener). Mix the two products together in a 2: 1 ratio. (For example, for 60 grams of mixture, mix to 40 grams of A and 20 grams of B.
• Make the mixtures using sensitive scales.
• For a better mixture, first add hardener to the mixing bowl and then add the resin on it and mix it for at least 2 minutes at a slow speed until a smooth appearance is obtained.
• You do not need to leave the prepared mixture to rest.
Considerations
• Prepare the resin and hardener mixture to a maximum of 100 grams. The product usage time will be shorter in mixtures with higher amounts and the mixture may become unusable.
• The working time of the mixture is 20 – 25 minutes. The prepared mixture should be used within the working time. Otherwise, the product will overheat and dry without mixing in the container.
• Volumetric measurements made with tools such as beaker, glass, syringe, etc. will cause incorrect mixing ratio. In order to adjust the mixture amount correctly, you must use sensitive scales.
• In order to minimize the formation of bubbles and air bubbles, take care to make the casting slowly and from a single point.
• You can use a hot air gun and / or smooth to remove bubbles formed on the surface after casting.
• In order to reduce the formation of air bubbles and bubbles in applications, a vacuum machine must be used.
• Resin should not be moved after it has started to gel. Otherwise, fluctuations in texture and surface may occur.
• Resin takes place approximately 12-16 hours after the initial drying. After the product is removed from the mold, it starts the final hardening process and this hardening process continues for 7 days.
• Work at room temperature. Low temperature can cause late drying and misting, and high temperature may cause early drying, yellowing and burning.
• Never heat the product during mixing and application.
• For any reason, do not mix any other material that does not fit into the system.
• Make sure that the equipment you use during the application is dry and clean.
• Do not forget to use safety equipment.
• Avoid contact with your skin. May have an allergic reaction.
• Store the product you do not use at a temperature of 10 and 30 degrees C in a closed area away from direct sunlight.
• Do not keep the products openly. • Do not leave the products obtained as a result of the mixture under direct sun.
• In-product yellowing may occur in the product waiting for a long time.
Cold ambient conditions cause the epoxy resins to whiten, solidify and have a candied appearance. When you observe these situations, your epoxy resin is crystallized. Soak the bottles in 60°C-80°C water until they become transparent, so that they can be reused.
Frequently Asked Questions
We have answered questions about the use of epoxy for you. Check out the frequently asked questions.
How much epoxy should I use?
Don’t know how much epoxy to use? You can easily calculate how much epoxy you need to use by entering the dimensions.
Slim Extra User Manuel
Ultra Clear Epoxy Resin System With Extra Yellowing Resistance
Suitable for small volume applications
Fully transparent
Does not contain volatile substances
Odorless
Bright
Solvent free
Does not contain volatile substances
Mixing ratio is 2:1 (by weight)
Jel time is
50-70 minutes
Demolding time is 18 - 24 hours
Usage
• The product is packaged as A (Resin) and B (Hardener). Mix the two products together in a 2:1 ratio. (For example, for 60 grams of mixture, mix to 40 grams of A and 20 grams of B.
• Make the mixtures using sensitive scales.
• For a better mixture, first add hardener to the mixing bowl and then add the resin on it and mix it for at least 2 minutes at a slow speed until a smooth appearance is obtained.
• Leave the prepared mixture to rest for about 5 minutes and then pour it onto the surface / mold you will apply and let it dry.
Considerations
• The working time of the mixture is 150 – 180 minutes. The prepared mixture should be used within the working time. Otherwise, the product will overheat and dry without mixing in the container.
• Volumetric measurements made with tools such as beaker, glass, syringe, etc. will cause incorrect mixing ratio. In order to adjust the mixture amount correctly, you must use sensitive scales.
• In order to minimize the formation of bubbles and air bubbles, take care to make the casting slowly and from a single point.
• You can use a hot air gun and / or smooth to remove bubbles formed on the surface after casting.
• In order to reduce the formation of air bubbles and bubbles in applications, a vacuum machine must be used.
• Resin should not be moved after it has started to gel. Otherwise, fluctuations in texture and surface may occur.
• Resin can be removed from the mold after approximately 18 -24 hours. After the product is removed from the mold, it starts the final hardening process and this hardening process continues for 7 days.
• Work at room temperature. Low temperature can cause late drying and misting, and high temperature may cause early drying, yellowing and burning.
• Never heat the product during mixing and application.
• For any reason, do not mix any other material that does not fit into the system.
• Make sure that the equipment you use during the application is dry and clean.
• Do not forget to use safety equipment.
• Avoid contact with your skin. You may have an allergic reaction.
• Store the product you do not use at a temperature of 10 and 30 degrees in a closed area away from direct sunlight.
• Do not keep the products openly.
• Do not leave the products obtained as a result of the mixture under direct sun.
• In-product yellowing may occur in the product while waiting for a long time.
Cold ambient conditions cause the epoxy resins to whiten, solidify and have a candied appearance. When you observe these situations, your epoxy resin is crystallized. Soak the bottles in 60°C-80°C water until they become transparent, so that they can be reused.
Frequently Asked Questions
We have answered questions about the use of epoxy for you. Check out the frequently asked questions.
How much epoxy should I use?
Don’t know how much epoxy to use? You can easily calculate how much epoxy you need to use by entering the dimensions.
Slim User Manuel
Clear Epoxy Resin System For Small Volume Applications
Suitable for small volume applications
Fully transparent
Odorless
Solvent free
Bright
Does not contain volatile substances
Mixing ratio is 2:1 (by weight)
Jel time is
50-70 minutes
Demolding time is
18 - 24 hours
Usage
• The product is packaged as A (Resin) and B (Hardener). Mix the two products together in a 2:1 ratio. (For example, for 60 grams of mixture, mix to 40 grams of A and 20 grams of B.
• Make the mixtures using sensitive scales.
• For a better mixture, first add hardener to the mixing bowl and then add the resin on it and mix it for at least 2 minutes at a slow speed until a smooth appearance is obtained.
• Leave the prepared mixture to rest for about 5 minutes and then pour it onto the surface / mold you will apply and let it dry.
Considerations
• The working time of the mixture is 90 – 120 minutes. The prepared mixture should be used within the working time. Otherwise, the product will overheat and dry without mixing in the container.
• Volumetric measurements made with tools such as beaker, glass, syringe, etc. will cause incorrect mixing ratio. In order to adjust the mixture amount correctly, you must use sensitive scales.
• In order to minimize the formation of bubbles and air bubbles, take care to make the casting slowly and from a single point.
• You can use a hot air gun and / or smooth to remove bubbles formed on the surface after casting.
• In order to reduce the formation of air bubbles and bubbles in applications, a vacuum machine must be used.
• Resin should not be moved after it has started to gel. Otherwise, fluctuations in texture and surface may occur.
• Resin can be removed from the mold after approximately 18 -24 hours. After the product is removed from the mold, it starts the final hardening process and this hardening process continues for 7 days.
• Work at room temperature. Low temperature can cause late drying and misting, and high temperature may cause early drying, yellowing and burning.
• Never heat the product during mixing and application.
• For any reason, do not mix any other material that does not fit into the system.
• Make sure that the equipment you use during the application is dry and clean.
• Do not forget to use safety equipment.
• Avoid contact with your skin. You may have an allergic reaction.
• Store the product you do not use at a temperature of 10 and 30 degrees in a closed area away from direct sunlight.
• Do not keep the products openly.
• Do not leave the products obtained as a result of the mixture under direct sun.
• In-product yellowing may occur in the product while waiting for a long time.
Cold ambient conditions cause the epoxy resins to whiten, solidify and have a candied appearance. When you observe these situations, your epoxy resin is crystallized. Soak the bottles in 60°C-80°C water until they become transparent, so that they can be reused.
Frequently Asked Questions
We have answered questions about the use of epoxy for you. Check out the frequently asked questions.
How much epoxy should I use?
Don’t know how much epoxy to use? You can easily calculate how much epoxy you need to use by entering the dimensions.